PRODUCTS

DuPont™ ISCEON 9 Series Refrigerants

IDS Refrigeration is a DuPont authorised distributor for the DuPont™ ISCEON® 9 Series range of Refrigerants. These are a unique range of easy to use, non-ozone depleting HFC retrofit refrigerants for HCFC and CFC equipment. Each has been developed to avoid costly equipment replacement for the owner and enable continued use of existing equipment with minimal downtime for retrofit. They can also offer other benefits depending on the refrigerant.

Time is running out for HCFCs with the phase out date for servicing of air conditioning and refrigeration equipment with virgin HCFCs rapidly approaching.

Compliance with EU environmental regulations has never been easier. With the complete family of ISCEON® 9 Series non ozone depleting HFC Refrigerants we provide easy, low cost retrofit solutions for contractors and end users alike. Many have already chosen these products to replace R22 and other HCFCs and their use is constantly growing.

IDS hold good stock levels of each of the products for immediate supply and in addition are able to provide guidance on their selection and use.

For further information on the refrigerant of choice see below and go to the download section where case studies, conversion guidelines and MSDS may be found.


DuPont™ ISCEON® MO29 (R422D)

DuPontTM ISCEON® MO29 (R422D) is an easy to use, non-ozone depleting HFC refrigerant blend of R125, R134a and R600a.

ISCEON® MO29 is used to replace R22 in a wide variety of high, medium and low temperature refrigeration applications as well as air conditioning and water chiller systems.
It has also been used in new equipment and selected ‘flooded' applications.

ISCEON® MO29 is a close match to R22 in terms of capacity and efficiency in most systems, but with a significantly lower discharge temperature which may prolong life of the compressor.

ISCEON® MO29 is compatible with traditional and new lubricants, providing easy, quick, cost effective retrofits and can be topped up during service without removing the entire refrigerant charge.

As ISCEON® MO29 is a blend it should always be removed from the cylinder as a liquid when charging a system.


DuPont™ ISCEON® 39TC® (R423A)

ISCEON® 39TC® (R423A) is an easy to use, non-ozone depleting HFC retrofit refrigerant blend of R134a and R227ea developed to replace R12 in centrifugal chillers.

ISCEON® 39TC® provides similar cooling capacity and comparable energy efficiency when compared to R12 with similar discharge pressures and temperatures.

ISCEON® 39TC® provides a quick, easy and cost effective retrofit typically requiring a single lubricant change to Polyol Ester without the need for flushing. It avoids the expensive engineering changes required to convert existing chiller equipment to R134a. This product can be topped up during service without removing the entire refrigerant charge.

As ISCEON® 39TC® is a blend it should always be removed from the cylinder as a liquid when charging the system.


DuPont™ ISCEON® MO49 (R413A)

ISCEON® MO49 (R413A) is a non-ozone depleting HFC retrofit refrigerant blend of R134a, R218 and R600a.

Please note that this product has been replaced with ISCEON® MO49PlusTM (R437A).

 


DuPont™ ISCEON® MO49Plus™ (R437A)

ISCEON® MO49PlusTM (R437A) is an easy to use, non-ozone depleting HFC retrofit refrigerant blend of R134a, R125, R600 and R601.

ISCEON® MO49PlusTM is suitable to replace refrigerants that replaced R12 in automotive, stationary air conditioning and direct expansion medium temperature stationary refrigeration systems.

It is an ideal replacement for HCFC containing blends R401A/B and R409A/B.

ISCEON® MO49PlusTM provides better cooling capacity and comparable energy efficiency to R12 but with lower discharge temperatures.

ISCEON® MO49PlusTM provides a quick, easy and cost effective retrofit and in most cases no change of oil is required as it is compatible with traditional and new lubricants. This product can be topped up during service without removing the entire refrigerant charge.

As ISCEON® MO49PlusTM is a blend it should always be removed from the cylinder as a liquid when charging the system.


DuPont™ ISCEON® MO59 (R417A)

ISCEON® MO59 (R417A) is an easy to use, non-ozone depleting HFC retrofit refrigerant blend of R125, R134a
and R600.

ISCEON® MO59 is typically used to replace R22 in direct expansion stationary air conditioning and medium temperature refrigeration systems.

ISCEON® MO59 has a significantly lower discharge temperature than R22, which may prolong the life of the compressor. In most systems ISCEON® MO59 provides the required cooling capacity and has shown energy savings (please see our download section). However, some systems may experience reduced capacity.

ISCEON® MO59 is compatible with traditional and new lubricants, providing easy, quick, cost effective retrofits and can be topped up during service without removing the entire refrigerant charge.

As ISCEON® MO59 is a blend it should always be removed from the cylinder as a liquid when charging the system.


DuPont™ ISCEON® MO79 (R422A)

ISCEON® MO79 (R422A) is an easy to use, non-ozone depleting HFC refrigerant blend of R125, R134a and R600a.

ISCEON® MO79 is typically used to replace R22, R502 and R22 containing blends such as R402A, R403B and R408A in medium and low temperature refrigeration systems. ISCEON® MO79 has a significantly lower discharge temperature compared to R22, and improved cooling capacity with a gain of up to 15% at low temperature conditions.
.
ISCEON® MO79 is compatible with traditional and new lubricants; providing an easy, quick, cost effective retrofit.

It has a lower global warming potential than R404A and R507, and can be topped up during service without removing the entire refrigerant charge.

As ISCEON®MO79 is a blend it should always be removed from the cylinder as a liquid when charging the system.


DuPont™ ISCEON® MO89

ISCEON® MO89 is a non-ozone depleting HFC retrofit refrigerant for R13B1 in low temperature direct expansion refrigeration systems.

ISCEON® MO89 is typically used in applications such as freeze dryers, medical freezers and environmental test chambers.

ISCEON® MO89 has cooling capabilities similar to R13B1 in many applications.

ISCEON® MO89 provides quick, easy and cost effective retrofits and in most cases no change of oil is required as it is compatible with traditional and new lubricants. This product can be topped up during service without removing the entire refrigerant charge.

As ISCEON® MO89 is a blend it should always be removed from the cylinder as a liquid when charging the system.

 


DuPont™ ISCEON® MO99 (R438A)

DuPontTM ISCEON® MO99 (R438A) is an easy to use, non-ozone depleting HFC refrigerant blend.

ISCEON® MO99 is ideally suited as an R22 replacement for all air conditioning and chiller applications with performance, capacity, mass flow and pressure characteristics a close match for R22. It has advantages over ISCEON® MO29 where the expansion valve has a fixed orifice or is closely sized to the capacity of the system. Whilst it has better capacity compared to ISCEON MO59.

ISCEON® MO99 is compatible with traditional and new lubricants, providing easy, quick, cost effective retrofits and can be topped up during service without removing the entire refrigerant charge.

As ISCEON® MO99 is a blend it should always be removed from the cylinder as a liquid when charging a system

For more information on ISCEON® MO99  please go to the download section where you can find more product information, case studies, conversion guidelines and a MSDS.